removing starter from the hole | Ford Powerstroke Diesel Forum
2016年2月21日 · With approx 75,000 miles on my 2015 F350, I decided to replace the POS oem starter with something better. The OEM starter had engagement issues. I installed a Mean Green gear reduction starter. Removing/installing a starter on the 6.7 is difficult; very little clearance and yes, you must disconnect the wires/cabled first.
'2011 6.7L Starter Issue - The Diesel Stop
2014年4月4日 · Symptom is that starter fails to engage and "free-spins" very occasionally. After it became a more frequent problem I took it to Ford but it would not fail and no indication of any other issue. I chose to replace the starter (at 45K miles) since the mechanism to engage the starter is contained within the starter housing.
2011 6.7L Starter Issue - Ford Truck Enthusiasts Forums
2014年4月5日 · I chose to replace the starter (at 45K miles) since the mechanism to engage the starter is contained within the starter housing. I noticed a small amount of oil present leaking from the starter gear train and assumed the issue was a dry/sticky shaft.
starter removal | Ford Powerstroke Diesel Forum
2014年6月25日 · Use a 13mm socket attached to a 6" extension. Then just hook your 3/8" ratchet to it and it comes right out. :thumb: You go over top of the starter from the bottom side of the truck btw. Yep, either reach in there blind, or remove the splash shield from the fender. it can be a pain but you will need a clip tool, 8mm, 11mm, and a 5.5mm.
6.7 Starter on a 6.0 PSD - Ford Truck Enthusiasts Forums
2020年10月3日 · I had to replace my 6.0 starter over a year ago and opted to use a 6.7 starter. The difference in spinning rpm was incredible!! The quick way to do this is the 6.4 starter. You don't need anything. that you don't already have with your 6.0L starter. The 6.0 starter cranking rpms in the video are to low.
'2011 6.7L Starter Problems - The Diesel Stop
2011年4月12日 · The starter may be bad, the sensor, or the sensor that senses that the sensor and starter sensors are working. The breakaway teeth on the ring gear are mandated by EPA to ensure starters are replaced before emissions eminate into the air.
6.7 2011 F350 Starter Change | Ford Power Stroke Nation
2013年12月22日 · Has anyone chnaged out a starter in their trucks yet? I am just looking for some tips to get to that 3rd bolt. My truck is dead in the driveway and it's -20 here right now. This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread. Write your reply...
Starter and flywheel issue. - Ford Truck Enthusiasts Forums
2023年4月14日 · OK, so on a '11 6.7 the starter and flywheel went bad and I had to replace the flywheel and starter on the engine. The easy way was to pull the cab, pull the transmission, and replace both flywheel and starter. Both parts were purchased from Ford. I got the job done last week and the truck has had very little use.
Putting 6.7 starter on 6.0 | Ford Powerstroke Diesel Forum
2017年10月19日 · I am a big fan of the 6.4 starter, my truck starts so much faster with it. The RPM is much faster then the 6.0 starter. A alternator upgrade is another must do wit these trucks to keep from having FICM issues etc. Batteries get topped off with juice when alt is 185 amp or larger. Everything electrical is better off.
Q&A: 6.7 Powerstroke Starter Replacement - Ford F350 Diesel - JustAnswer
ARE YOU SURE ON 1 HOUR HAVE BOLTS OUT AND NOT ENOUGH ROOM TO GET OLD STARTER OUT. Here is a screenshot of the labor time guide: https://goo.gl/GqyX6L. Here is the repair manual procedure in PDF format: https://goo.gl/W3gQTP.